Beko Freezer Not Freezing [Solved]

You’ve bought a new fridge freezer from Beko, but it won’t freeze food properly.
What should you do?
Fridge freezers are great at keeping food fresh, but they don’t always get the job done.
If you’ve got a problem with your fridge freezing, then you’ll want to check out our guide on how to fix a frozen fridge.
: Fridges aren’t perfect, but they’re pretty good at keeping food cold.
If you’re having trouble with your fridge freezing, you might want to consider buying a new model

Beko Fridge Freezer Not Cooling or Freezing – What to Do

If you have a Beko fridge freezer and it is not freezing or cooling properly, try these steps below: 1 Check if the ice maker is working correctly. To check if the ice maker is functioning correctly, remove the ice tray from the freezer and place it into the sink. Turn off the power to the unit and wait 30 seconds. Then turn the power back on and see if any ice cubes form. If no ice cubes form, replace the ice tray and repeat step 2. 2 Make sure the door seals are closed tightly. If the doors are open, cold air could enter the freezer and prevent the freezer from cooling down. Close the doors and test again.

1. Condenser Coils

Condensers are coils located outside the refrigerator where warm air is cooled. This cool air is used to maintain the interior of the refrigerator at a constant temperature. A condenser coil is usually mounted on the exterior wall of the refrigerator near the top of the refrigerator. It consists of two metal tubes connected together. One tube is called the evaporator coil and the other is called the condenser coil. The evaporator coil absorbs heat from the refrigerant gas circulating around it. As the gas passes through the evaporator coil, it becomes cooler and releases heat. The condenser coil receives the cooled refrigerant gas and transfers the heat to the surrounding air.

2. Condenser Fan Motor

A fan motor is a mechanical device that converts electrical energy into mechanical energy. It is used to move air across a surface. In a refrigerator, the fan motor moves cold air across the evaporator coil. 3. Evaporator Coil An evaporator coil is a copper tubing that is wrapped around the condenser coil. It is attached to the condenser coil using a clamp. The evaporator coil is designed to absorb heat from the refrigerant passing through it. As the refrigerant flows through the evaporator coil it heats up and changes state from a liquid to a vapor. The vapor is then compressed by the compressor and sent back to the condenser coil.

3. Evaporator Fan Motor

A fan motor is a mechanical machine that converts electricity into mechanical energy. It uses electric current to create force. In a refrigerator, a fan motor turns a fan blade to push air across the evaporator coils. This helps cool the interior of the refrigerator. 4. Refrigerant Refrigerant is a gas that is used to transfer heat between two different places. It is found in many household appliances such as refrigerators, freezers, air conditioners, and heat pumps.

4. Thermistor

Thermistors are electronic components that measure the temperature of something. A thermistor is a resistor whose resistance changes according to the temperature. Thermistors are used to monitor temperatures in industrial processes, medical equipment, and other devices. 5. Thermostat Answer: A thermostat is a device that controls the temperature of a system. It senses the temperature and sends signals to turn power on or off. Thermostats are used in heating systems, cooling systems, and air conditioning systems.

5. Start Relay

A start relay is a switch that opens and closes electrical circuits. It allows electricity to flow from the source to the load. It is used in many applications such as lighting fixtures, motors, solenoids, and relays. 6. Transformer Answer: Transformers are devices that step down voltage levels. They are used to convert alternating current AC into direct current DC. They are used in electric generators, transformers, and rectifiers.

6. Start Capacitor

Capacitors store energy temporarily. They are used in power supplies, audio amplifiers, and radio transmitters. 7. Resistor Answer: Resistors are components that regulate current flowing through a circuit. They are used in appliances, electronic equipment, and computers.

7. Temperature Control Thermostat

Thermostats are devices that measure the temperature of a particular area and adjust the heating or cooling system accordingly. They are used in many types of appliances such as refrigerators, air conditioners, and ovens. 8. Relay An electromechanical switch that opens or closes electrical circuits. It is used in many applications such as lighting, motors, and appliances.

Beko Freezer Not Freezing – How to Fix

1. Check if the freezer is plugged into power source. 2. Make sure the door is closed properly.

1. Check the Evaporator Fan Motor

Beko freezers have two evaporator fans. One fan is located on top of the freezer and another fan is located on bottom of the freezer. The evaporator fan motor is responsible for circulating air throughout the freezer. If the evaporator fan motor does not function properly, the freezer will not circulate cold air throughout the freezer. This could lead to ice build up on the walls of the freezer. To fix this problem, follow these steps: Step 1: Remove the back panel from the freezer. Step 2: Disconnect the wires connected to the evaporator fan motor.

2. Check the Start Relay

Check the start relay for proper operation. The start relay is used to turn on the power supply to the evaporator fan motors. If the start relay is defective, the evaporator fan motors will not operate. To check if the start relay is working correctly, remove the back panel from the refrigerator and disconnect the wires connected to the start relay. Then, press the button on the start relay. If the light turns green, the start relay is functioning normally.

3. Check the Condenser Fan Motor

To check if the condenser fan motor is operating properly, open the door of the refrigerator and pull the condenser fan motor assembly off the wall. Remove the two screws holding the condenser fan motor to the wall. Disconnect the wire connected to the condenser fan motor. Press the button on the condenser fan motor and observe whether the light comes on. If the light does not come on, the condenser fan motor may be malfunctioning. 4. Check the Evaporator Fan Motor Answer: To check if the evaporator fan motor is operating properly, open the door of the freezer and pull the evaporator fan motor assembly off the floor. Remove the two screws securing the evaporator fan motor to the floor. Disconnect the wire attached to the evaporator fan motor. Press the switch on the evaporator fan motor and observe whether it lights up. If the light does come on, the evaporator fan motor may be malfunctioned.

4. Check the Condenser Coils

To check if the condenser coils are working properly, remove the condenser from the unit. Unplug the wires connected to the condenser coils. Turn the power back on and press the buttons on the condenser. Observe whether the condenser fan turns on. If the fan does not turn on, the condenser coils may be malfunctioning. Replace the condenser coil and reattach the condenser to the unit. 5. Check the Refrigerant Line Answer: To check the refrigerant line, remove the cap from the end of the refrigerant line. Pull the refrigerant line out of the unit. Connect the hose to a container filled with water. Observe whether bubbles form in the water when the line is pulled out of the unit. If no bubbles appear, the refrigerant line may be damaged. Replace the refrigerant line and reconnect the cap.

5. Check the Evaporator Coils

To check the evaporator coils, remove the cap from each of the evaporator coils. Remove the screws holding the evaporator coils in place. Rotate each of the evaporator coil until the coils are free from the cabinet. Inspect the coils for damage. If any of the coils are cracked or broken, replace the coils. 6. Check the Heat Exchanger Answer: To check if the heat exchanger is functioning properly, remove the cap from one side of the heat exchanger. Pull the heat exchanger out of the unit. Disconnect the wire connected to the heat exchanger. Turn the power back off and press the buttons on both sides of the heat exchanger simultaneously. Observe whether the heat exchanger fan turns on. If no fan turns on, the heat exchanger may be damaged. Replace only the heat exchanger and reattach the cap.

6. Check the Temperature Control Thermostat

Check the temperature control thermostat for proper operation. Remove the cap from the top of the temperature control thermostats. Remove the screws holding it in place. Remove the wires attached to the temperature control thermostatic. Press the button on the thermostat to see if the temperature control thermostatin is working. If the temperature control thermostatal does not function properly, replace the thermostat. 7. Check the Water Level Sensor Answer: To check the water level sensor, remove the cap from the bottom of the water level sensor. Remove the screws holding in place. Remove the wire connected to the water level sensor. Press the button on both sides of the water level sensor simultaneously. Observe whether either side of the water level sensor functions properly. If either side of the water levelsensor does not work properly, replace the water level sensor.

How do I fix my freezer not freezing?

Frigidaire Freezers have a reset button located near the top right corner of the door. It is used to turn off the freezer and restart it. To turn the freezer back on, push the button again.

What is the ideal temperature for a Beko freezer?

Beko freezers are designed to maintain a constant temperature throughout the unit. This is achieved by using a thermostat that regulates the flow of coolant into the refrigeration system. A Beko freezer uses a closed loop cooling system where the evaporator coil is immersed in a liquid called “coolant”. The coolant absorbs the heat from the air surrounding the coils and transfers it to the interior of the refrigerator. The coolant circulates continuously through the coils until it reaches the condenser coil. Here, the coolant releases the absorbed heat back into the environment.

Where is the reset button on my Frigidaire freezer?

Freezers are great tools for keeping food frozen until needed. However, if your freezer isn’t working properly, it could mean that something is wrong with the compressor or the fan motor. To check these components, turn off the power switch and remove the back panel from the freezer. Look for any signs of damage or corrosion. If everything looks good, try restarting the unit. If the problem persists, contact a professional repair service.

Daisy Kim
Latest posts by Daisy Kim (see all)

Leave a Comment