Last Updated on March 18, 2022
Your Kenmore refrigerator keeps making ice.
What should you do?
The Kenmore brand has been around since the 1950s and is known for its high quality appliances.
In recent years, the company has also become famous for their line of refrigerators.
However, some Kenmore refrigerators have had problems with ice production.
If you are experiencing this problem, don’t worry.
There are several ways to fix it
Kenmore Refrigerator Keeps Making Ice – What to Do
If your refrigerator keeps making ice, it could mean that the compressor isn’t working properly. This is usually caused by a bad capacitor a component used to store energy. To fix this problem, you’ll need to replace the capacitor. It’s not difficult to replace, but if you don’t know how to do it, you’re better off calling a professional repairman.
1. Feeler Arm
To remove the door panel, you’ll first need to disconnect the power cord from the wall outlet. Then, turn off the power switch located near the front of the fridge. Next, lift the bottom edge of the door panel using the feeler arm. Once you have lifted the panel, slide it forward until it stops. Remove the old capacitor and place it into a plastic bag. 2. Door Panel Answer: Once you have removed the bottom edge of the panel, you’re ready to pull the panel away from the rest of the door. Slide the panel toward the back of the fridge until it stops. Remove any screws holding the panel to the frame. Place the new capacitor into the opening where the panel was attached. Replace the screws and tighten them down.
2. Plastic Paddle
Remove the two screws holding the paddle to the door. Pull the paddle away from the door. Remove the old capacitor from the paddle and replace it with the new one. Reinstall the screws and tighten them. 3. Door Handle Answer: Pull the handle away from the door. Lift the handle up and remove the four screws holding the handle to the door. Remove the handle and set aside.
3. Water Inlet Valve
Turn off the power switch and open the drain valve. Turn the knob clockwise until the water stops draining. Replace the water inlet valve. Close the drain valve and turn the power switch back on. 4. Drain Valve Answer: Open the drain valve and remove the cap. Open the drain valve and pull the drain hose out of the hole. Remove the rubber washer and install the new washer into the hole. Tighten the screw.
How do you unclog a side by side freezer drain?
If your ice maker isn’t making any ice, check the following: 1 Make sure the ice tray is full of water. 2 Check the drain line from the ice maker to ensure it’s not clogged. 3 Clean the ice mold and the ice bin. 4 Make sure the ice maker is plugged into power. 5 Check the ice maker manual for troubleshooting tips. 6 Try adding more ice trays if needed. 7 If the above steps didn’t help, call us at 888-865-5346.
How do you unclog a Kenmore freezer drain?
Kenmore freezers are designed to freeze items quickly and efficiently. However, if you leave the door open for long periods of time, the cold air from the freezer will leak into the refrigerator causing it to get colder. This is why you should always close the door after using the freezer.
How do you keep ice from building up in the freezer?
Defrost drains are located under the bottom shelf of the freezer drawer. To access them, remove the bottom shelf. Look for two holes about 1/2 inch apart. One hole leads into the defrost drain tube while the other leads into the main drain tube.
Where is the freezer drain on a Kenmore side by side?
Kenmore side by side refrigerators have a freezer drain located under the bottom shelf. It is used to remove ice from the freezer. To access the drain, lift the bottom shelf and pull down the plastic piece that covers the drain.
Where is the defrost drain in my Kenmore freezer?
Ice builds up in the freezer because the air inside the freezer is not being replaced properly. This leads to condensation and moisture buildup. To prevent this, you should periodically open the door and let cold air into the freezer. This will help dry out the air inside the freezer and reduce the chances of ice build up.
Why does my Kenmore freezer ice up?
Kenmore freezers have a drain tube that runs from the bottom of the freezer to the top where it empties into a sink. This drain tube gets clogged easily because of ice buildup. To clean the drain tube, remove the front panel of the freezer and locate the drain tube. Remove any debris that may be blocking the drain tube. Clean the drain tube using a soft brush or wire scrubber. Make sure to turn off the power supply to the unit while cleaning the drain tube. Once the drain tube is cleaned, replace the front panel and reattach the power supply.
Why won’t my ice maker stop filling?
If you notice any ice buildup around the drain line, you can remove it easily using a spoon. First, turn off the power supply to the unit. Then, open the door and remove the ice from the drain line. Next, pour hot water into the drain line until it runs clear. Once the drain line is clear, shut off the faucet and let the water run clear again. After that, turn on the power supply and reattach the ice.
- 3 Ingredient Lemon Pie - March 27, 2022
- How To Store And Serve Ice Cream Cake? - March 27, 2022
- How To Cook Frozen Lasagna Faster? - March 27, 2022